ISP1 Working Parameters
• Hardness must be 3 grains or higher
• pH 6.5 to < 7.0 (ISP1-1044)
• pH 6.0 to < 7.0 (ISP1-1054 and 1354)
• TDS must be 80 ppm or higher
|
ISP2 Working Parameters
• Hardness must be 3 grains or higher
• pH should be 7.0 or greater
• TDS must be 80 ppm or higher |
NOTES:
1. pH or TDS less than listed amount above will greatly reduce media's service life.
2. Hardness less than 3 grains will reduce softening capacity over a short period of time. |
MODEL |
ISP1-1044 |
ISP1-1054 |
ISP1-1354 |
ISP2-1044 |
ISP2-1054 |
ISP2-1354 |
1 Capacity:
(Grains/Lbs NaCl) |
Maximum |
11,800 @12.4 |
22,600 @ 15.9 |
36,900 @ 21.2 |
20,300 @ 12.4 |
34,800 @ 15.9 |
60,300 @ 26.5 |
Medium |
11,400 @ 9.3 |
20,700 @ 12.4 |
33,600 @ 15.9 |
19,100 @ 9.3 |
32,000 @ 12.4 |
48,300 @ 15.9 |
Minimum |
7,300 @ 3.2 |
16,400 @ 6.1 |
28,300 @ 9.5 |
11,100 @ 3.2 |
22,900 @ 6.1 |
28,200 @ 9.3 |
| Amount of Media (Cu. Ft.) |
1.0 |
1.5 |
2.5 |
1.0 |
1.5 |
2.5 |
| Maximum Water Hardness (GPG) |
20 |
30 |
40 |
40 |
60 |
80 |
| 2 Maximum Iron (PPM) |
8.0 |
10.0 |
15.0 |
8.0 |
10.0 |
15.0 |
| 3 Minimum pH Required |
6.5 |
6.0 |
6.0 |
7.0 |
7.0 |
7.0 |
4 Total pH Adjusted Water at
Continuous Flows |
630 |
252 |
432 |
NA |
NA |
NA |
| 5 Peak Flow Rate (GPM @ P-PSI) |
19 @ 15.0 |
17 @ 15.0 |
19 @ 15.0 |
19 @ 15.0 |
17 @ 15.0 |
19 @ 15.0 |
| Continuous Flow Rate (GPM @ P-PSI) |
9.0 @ 5.0 |
8.0 @ 5.0 |
9.0 @ 5.0 |
9.0 @ 5.0 |
8.0 @ 5.0 |
9.0 @ 5.0 |
| Water Pressure Range (PSI) |
25-100 |
|
|
|
|
|
| Water Temp. (ºF) |
33-100 |
33-100 |
33-100 |
33-100 |
33-100 |
33-100 |
| Electrical Requirements (volts-hertz) |
110-50/60 |
110-50/60 |
110-50/60 |
110-50/60 |
110-50/60 |
110-50/60 |
| Pipe Size |
1" |
1" |
1" |
1" |
1" |
1" |
| Total Dimensions: |
Media Tank |
10"W x 52"H |
10"W x 62"H |
13"W x 62"H |
10"W x 52"H |
10"W x 62"H |
13"W x 62"H |
Brine Tank |
18"W x 40"H |
18"W x 40"H |
18"W x 40"H |
18"W x 40"H |
18"W x 40"H |
18"W x 40"H |
1 All ISP Water Conditioners are pre-factory set at medium salting. Note: influent waters must be at least 3 GPG hardness and 80 TDS. A calcite or corsex unit may be needed for correct operation.
2 Iron removal may vary depending on form of iron, pH and other local conditions. On waters that are pre-chlorinated or where other pre-oxidation occurs, an iron precipitate can form that is too small to be filtered.
3 The pH listed is the minimum for the influent water.
4 This is the minimum number of gallons at the continuous flow rate corrected to a 7 pH. The actual amount of pH adjusted water may be greater.
5 Unit not tested for capacity at these flow rates. Water quality may vary.
MODEL |
ISP1-1044 |
ISP1-1054 |
ISP1-1354 |
ISP2-1044 |
ISP2-1054 |
ISP2-1354 |
|
MIN. |
GAL. |
MIN. |
GAL. |
MIN. |
GAL. |
MIN. |
GAL. |
MIN. |
GAL. |
MIN. |
GAL. |
Backwash |
12 |
42 |
12 |
48 |
12 |
84 |
12 |
36 |
12 |
42 |
12 |
60 |
Brine & Rinse |
72 |
29 |
90 |
36 |
90 |
72 |
72 |
29 |
90 |
36 |
90 |
72 |
Rapid Rinse |
4 |
14 |
4 |
16 |
4 |
28 |
4 |
12 |
4 |
14 |
4 |
20 |
Brine Refill |
6 |
3 |
10 |
5 |
12 |
6 |
6 |
3 |
10 |
5 |
12 |
6 |
Total |
94 |
88 |
116 |
105 |
118 |
190 |
94 |
80 |
116 |
97 |
118 |
158 |
Review literature or find out more!
|
